Jui-Deng Industrial Corp.

Tainan, 
Taiwan
http://www.mospectools.com.tw
  • Booth: 1544


Welcome to MOSPEC, Distributor Wanted! www.mospectools.com.tw

MOSPEC has more than 1000 different products, including tools for fork, shock, suspension, chain, valve, tire, bearing, piston, carburetor, flywheel puller, axle, clutch, and many other best-selling tools kits. MOSPEC also makes special tools for DUCATI, TRIUMPH, POLARIS, HARLEY-DAVISON, BMW, APRILIA, MV AGUSTA, MOTO GUZZI, SKI-DOO, YAMAHA, HONDA, SUZUKI, and KAWASAKI. 100% made in Taiwan, high-quality products and on-time delivery are MOSPEC’s strengths. MOSPEC is dedicated to constantly developing new items and providing our customers with a wide variety of products. We have stock for all the products to ensure a stable supply. Visit our Youtube channel to find out more!

Brands: MOSPEC Motorcycle Specialized Tools

 Products

  • Fork Seal Drivers Set
    Set supplied with 9 essential drivers for easy installation of most fork seals on either conventional or inverted forks....

  • Front And Rear Wheel And Chain Service Tool Kit
    This kit provides two chain adjusters, three wheel nut sockets and three front axle alignment tools for Ducati...

  • Front and Rear Wheel Nut Tool Set
    Set provides one combined socket and 4 sockets. It also provides 3 O-rings for replacement.

    The combined socket is two sizes in one, a 55mm 12pt for the rear and a 28mm 6pt for the front...

  • Shaft Holding Tool Set
    There are magnets on the tool to prevent falling while service.
    It can hold shock shafts, fork cartridges, damping rods or other round shafts while servicing.
    Size : 14, 16, 18, 32, 35, 10, 12, 12.5, 14, 20, 24, 29 mm and 1/2＂...

  • Piston Ring Compressor Set
    Includes pliers and six bands.
    Use the pliers with any band to install pistons from 2-7/8＂to 4-3/8＂in diameter (73mm to 111mm)....

  • 9-Piece Stud Removal & Installation Tool Set
    This tool set provides various sizes for stud installation.
    Sizes as the following :
    7/16＂-14, 7/16＂-20, 7/32＂Allen wrench (852A)
    3/8＂-16, 3/8＂-24, 3/16＂Allen wrench (852B)
    5/16＂-18, 5/16＂-24, 5/32＂Allen wrench (852C)
    1/4＂-20, 1/4＂-24, 1/4＂-28, 1/8＂Allen wrench (852D)...

  • Wheel Bearing Removal/Installation Tool
    It is ideal tool to remove and install sealed type wheel bearings without damaging the wheel.
    It can be used on 3/4＂and 1＂I.D. bearings 2000-2006 and 25mm bearings on most 2007-2008 models with or without ABS....

  • Fork Stem/Main-Shaft Bearing Tool Kit
    This combined tool kit helps you to pull and install fork stem bearing and main-shaft bearing inner race easily on your H-D motorcycle....

  • Inner Cam Bearing Removal And Installation Tool Kit
    This kit works on all H-D Twin Cam 88 engines.

    Inner Cam Bearing Removal Tool :
    Designed to remove the bearing easily without damage the crankcase and also prevent the pin rollers falling into the crankcase.

    Inner Cam Bearing Removal and Installation Tool :
    It used to install the two inner cam needle bearings on the Twin cam....

  • Inner Cam Bearing Remover & Installer Tool Kit
    The remover tool ensures that the bearing rollers won’t drop into crankcase. The installation driver sets the cam bearing to its proper depth.
    Fit 2017-UP Harley-Davidson Milwaukee Eight engines (single camshaft design)....

  • Bearing And Exhaust Seal Service Tool Set
    Set for use by service wheel bearing race, steering head bearing race,sprocket shaft bearing race,cam bearing and exhaust seal on Harley-Davidson motorcycles....

  • Valve Spring Compressor Tool Set
    Ideal tool set to compress valve springs for removal or installation. Included collars for Conical Valve Springs and Milwaukee Eight Valve Spring.

    Fit most Big Twin and XL models, new Milwaukee Eight series engine....

  • Combination Flywheel Puller Driver Set
    10 pieces kit provides 15 different applications.
    sizes as follows ：
    M14 x 1.5, M16 x 1.5, M18 x 1.5, M19 x 1.0, M20 x 1.0, M27 x 1.25, M22 x 1.0, M25 x 1.5, M22 x 1.5, M26 x 1.5, M24 x 1.0, M27 x 1.0, M26 x 1.0, M28 x 1.0,
    M28 x 1.5.
    Except for M27 x 1.0, all applications have right hand threads....

  • Deluxe Suspension Bearing Service Tool
    Ideal tool set to remove and install of suspension linkage and swingarm pivot bearings.
    Included one of blind bearing puller for removal of 20 mm blind bearings.

    Fits most off-road motorcycles & ATV’s, used on 20 & 22 mm I.D. bearings....

  • Bearing Driver Set
    Set fits bearing with 8-30 mm I.D. and 32-47 mm O.D.

    Set provides one durable steel handle and 12 sizes of anodized aluminum adapters :
    8mm, 10mm, 12mm, 15mm, 17mm, 20mm, 25mm, 30mm, 32mm, 35mm, 40mm and 47mm.

    Set can be used with a hammer or shop press.

    Taiwan pat. pending...

  • Blind Bearing And Bushing Removal Set
    Set provides slide-hammer, crossbar type shaft and 30, 25, 20, 17, 15, 12, 10 and 8mm collets.

    Crossbar type shaft allows the collet is easy of removal....

  • Wheel Bearing Remover Set
    Set contains large and small driver rods, 10mm, 12mm, 15mm, 17mm, 20mm, and 25mm collets. Dependable split collet design allows user to drive the bearing out of the hub easily....

  • Crankcase Separator Tool
    Fits most 2-stroke & 4-stroke engines with vertically split cases.
    It allows a multitude of bolt patterns to be used.
    It eliminates binding under heavy loads.
    It provides 6mm mounting bolts (M6 x 1.0 x 200), 8mm mounting bolts (M8 x 1.25 x 200) and crankcase separator center bolt with 24mm hex....

  • Flywheel Puller Set
    This puller set removes most current Polaris flywheels.

    Shaped slots design allows to use on all 2-stroke snowmobile models....

  • Ball Joint Replacement Tool
    Used to remove and install the lower ball joints on Polaris ATV and side x side models with pressed-in ball joints on the front strut casting....

  • Drive Clutch Fixture
    It provides three M12 x 1.75 x 15mm cap screws for use with the Yanmar diesel drive clutch.
    This fixture helps you to hold the stationary sheave when removing the spider on Polaris ATV and RANGER drive clutches....

  • Belt Removal and Clutch Compression Tool Kit
    Ideal tools kit to remove / replace bell and service clutch compression.

    Fits Polaris ACE 325/570/900, 570/800/900/1000 RZR, Turbo, RS1, General & Ranger XP 900 with TEAM Tied Clutch....

  • Clutch Compression Tool
    Fits multiple ATV and snowmobile clutches.
    ATV/UTV
    Applications :
    Polaris, Kawasaki and Comet primary clutches.
    Polaris EBS/Roller, Kymco, Yamaha, Arctic Cat and Suzuki secondary clutches.
    Kawasaki Prairie, KFX 700, 650/750 Brute Force, 750 Teryx secondary clutches.
    Polaris RZR (all models), 700 & 800 Sportsman, any two roller secondary clutches
    Snowmobile
    Arctic Cat, Comet, Polaris, Ski-Doo and Yamaha primary clutches....

  • Clutch Bushing Replacement Tool Kit
    Ideal tool kit to remove and replace clutch drive and drive bushings on all Polaris ORV and snow clutches....

  • Chain Breaker And Riveting Tool Kit
    The kit supplied with adequate components to break chains from #35 to #630. It can be used on cam chains and drive chains....

  • Piston Ring Tool
    Designed to prevent ring breakage during cylinder installation....

  • Transmission Case Shifter Shaft Seal Installer Tool
    Ideal tool to install H-D seal No.12045 on all Big Twins 1980 to 2006 using a 5-speed transmission case....

  • Transmission Case Shifter Shaft Seal Installer Tool
    Ideal tool to install the shifter shaft seal in the transmission case. Tool is piloted to ensure no damage to seal during installation.

    Fits 1980-2006 Big Twins, (except o6 Dyna)....

  • Transmission Case Shifter Shaft Seal Installer Tool
    Ideal tool to install H-D seal No.37101-84B on 2006 to present H-D 6- Speed Cruise Drive transmissions, and Sportsters 1984 to 2005...

  • Cam Chain Tensioner Tool
    Used to unload pressure on the primary and secondary chain tensioners when servicing H-D Twin Cam 88 engines.
    Also checks spring loads on chain tensioners.

    Works on all 1999-06 FL, 1999-05 FXD and 2000-06 FXST....

  • Crankshaft Turning / Rotating Tool
    This tool use to rotate your crankshaft, turning your engine over while it is in the chassis or on the workbench. This engages the splines on the primary (left) side of the crankshaft and can be turned using a 3/4 inch wrench on the hex.
    Fits Harley-Davidson Big Twins from 1954-2005....

  • 2pcs Cylinder Hold Down Nuts Tools
    Ideal tools to provide an effective way to keep the cylinders in place when the heads are removed from the engine.
    Also useful when installing the second cylinder over the piston and rings after the first cylinder has been installed.
    It is also useful to have the cylinders secured when rotating the crankshaft for other work....

  • Tappet Guide Puller Tool
    Removes press-fit tappet guides from the crankcase after tappet body adjusting screw is removed.
    Fits 1957-1983 Harley-Davidson Ironhead Sportsters....

  • Oil Drain Spigot Tool
    It channels the transmission fluid from the bottom of your transmission case into the drain pan instead of onto your frame.
    It fits Harley-Davidson FLT 2009-UP V-twin....

  • Clutch Adjuster Nut Tool
    Fits all 1998 and later H-D Big Twin models excluding applications with hydraulic clutches.
    Deep socket design, can be driven with 11/16＂socket wrench....

  • Crankshaft Jam Tool
    It helps user to lock the crankshaft through the timing mark hole while performing timing work.
    Fits most Classic, XL Sportster & FL Big Twins Models.
    Lubricate all areas before use....

  • Pushrod Tube Holder Tool
    This holder makes adjustment of adjustable pushrods easily, holding pushrod tubes up and out of the way....

  • Primary Drive Holding Tool
    This wedge is used to hold the primary chain for removal and installation of the engine sprocket nut without damaging the primary gear.

    It fits on all H-D big twins models, except 06 Dyna, 07-up big twins. Material : POM...

  • Rocker Stud Removal/Installation Tool
    Fits Harley-Davidson 45s 1930-52....

  • Ignition SwitchFork Lock Tool
    Simplifies the process of removing and installing the ignition switch/fork lock.
    Mounts on ignition switch face nut that holds switch in place, letting you remove or install switch correctly without damage.
    3/8＂drive access hole.
    Fits H-D Dyna models 2006-present.
    Refer to H-D service manual and wear safety glasses or other face and eye protection....

  • Fork Cap Socket
    Socket use for removal and installation of the fork cap nut (1-3/8” hex) on most HD Big Twin and Sportster models.
    The O-ring insert design allows you without damaging the top of the cap while operating.

    This thin socket has a 1/2” square drive....

  • Cam/Crank Sprocket Locking Tool
    It helps the user to lock the camshaft and crankshaft sprockets to remove, replace and torque the sprocket bolts properly.

    Applications : H-D FXD models 2006-present....

  • CamCrank Sprocket Locking Tool
    It helps the user to lock the camshaft and crankshaft sprockets to remove, replace and torque the sprocket bolts properly.

    Applications : H-D FLH models 1999-present, FXD models 1999-2005 and FXST models 2000-present....

  • Ignition Points Timing Tool
    It helps you to lock ignition points to advanced position during tune-ups and distributor work.
    Fits 1970-1978 Harley Davidson big-twins models.
    Lubricate all areas before use....

  • Pinion Gear Locking Tool
    Ideal tool to lock pinion gear when torquing the pinion gear nut.
    Simple to use, align underneath gear and screw into case.

    Fits Harley Davidson XL 91-99, Buell....

  • Pinion Gear Locking Tool
    Ideal tool to lock pinion gear when torquing the pinion gear nut.
    Simple to use, align underneath gear and screw into case.

    Fits Harley Davidson Sportsters & Buells 1991 to 1999....

  • Oil Filter Wrench
    74mm x 14 flat.
    24mm external hex head with 1/2＂square drive.
    Material : Aluminum 6061....

  • Pinion Gear Locking Tool
    Tool provides a simple way to lock pinion gear when tightening the pinion gear nut.
    Easy to use, just align underneath gear and screw into case.


    It fits Harley Davidson Big Twin 1954-1999 single cam only (Includes aftermarket and S&S motors)...

  • Gear Select Tool
    This tool helps you to position gear engagement fork.

    It fits Ducati motorcycles....

  • Fork Cap Tool
    Ideal tool to remove and install the fork cap.

    Fits most＂OHLINS＂suspension models.

    There is a square hole on the backside for a 1/2＂drive.
    The rubber cushion design allows you without damaging the fork cap while using.
    Material : 7075-T6 aluminum....

  • Fork Cap Tool
    Tool is used for older FG series Ohlins forks.
    Does not fit newer FGRT forks or Cartridge Kits.
    Tool comes with a 24mm hex on top as well 3/8＂square hole that fit a ratchet/torque wrench....

  • Fork Cap Tool
    Use for OEM Ducati Panigale 1199S Ohlins Forks and 2015 Yamaha R1 with Ohlins forks.
    Tool comes with a 24 MM hex on top as well 3/8＂square hole that fit a ratchet/torque wrench....

  • Clutch Cover Removal Tool
    Fits all V-twin Bevel Ducati engine for narrow or wide case singles, round or square case....

  • 14mm/15mm Cylinder Head Nut Torque Tool
    These tools enable you to properly torque the 14mm and 15mm cylinder head nuts.

    There is a square hole on these tools for a 1/2 inch drive.
    15mm torque tool fits on all modern 2V and 4V Ducati's (Monster, Multistrada, 748, 749, 750, 851, 888, 900, 916, 996, 998, 999, 1000).
    14mm torque tool fits on the newer 4V Ducati's (600, 620, 848, 1098, 1198 and Similar)....

  • Timing Pulleys Locking Wrench
    Used to lock into the elastic nut that holds the timing pulleys onto the camshafts.

    Monster S2R Modell 500 SL Pantah 750 Paso '84-'92 750 Sport Ducati 750 SS '91 Ducati 750 SS '92 Ducati 750 F1/Laguna Seca Ducati 900 SS '90 Ducati 900 SS '92 Ducati 900 SS/SL '94-'97 Ducati 906 Paso '88 Ducati 907 I.E. '92 Ducati Monster 600 '94 Ducati Monster 900 '93 Ducati Monster 900 '9...

  • Belt Roller Timing Tool
    Fits Diavel, Hypermotard, Monster, Multistrada, Streetfighter, Superbike....

  • Seal Ring Driving Tool
    Ideal tool for seal ring driving.
    Fits Ducati Panigale models....

  • Fork Pin tool
    Ideal tools for 4-holes Marzocchi SW21 fork.

    Applications: 
    Ducati 750 Paso , BJ 1986 - 1990
    Ducati 851 S , BJ 1988 - 1990
    Ducati 851 S Tricolore , BJ 1988 - 1988
    Ducati 906 Paso , BJ 1989 - 1992
    Ducati 907 Paso i.e. , BJ 1990 – 1993...

  • Cam Pulley Nut Tool
    The holding tool allows you to hold the camshaft timing pulley from rotating and the socket tool to loosen and tighten the cam pulley retaining ring nut.

    It fits Ducati Pantah and other 2 valve belt drives, as well as 4 valve 916 belt drives.
    Tool provides one holding tool and one socket tool with 1/2” drive....

  • Engine Rotating Tool
    It allows you to rotate your engine easily and safely while checking the valve clearances or setting the timing.

    It works on Ducati Monster/748/996/999/SS....

  • Foot Break/Shifter Bolt Removal Tool
    Ideal tool to prevent damage to the bolts or your bike while removing the foot break/shifter bolts. Tool has a 1/2＂drive.

    It fits Ducati Desmosedici RR models....

  • Camshaft Alignment Tool
    It allows you to keep the camshaft sprockets correctly aligned while installing of new cam belts.
    It also helps you to remove the nut attaching the pulley to the camshaft.
    Install the tool with lobes on the camshaft with the nut to be removed.
    Use a spanner socket to remove the nut.
    It fits the Ducati 851, 888, 916 and 996 engines....

  • Cam Belt Lock Tool
    It helps you to hold the loaded cam from rotating while installing the belts on 4 valve Ducati engines.
    It will not fit st4 or s4 engine.
    Slide the tool between the cam belt pulleys and slide the old belt off.
    It fits Ducati 748, 916, 996, and Desmoquattro....

  • Short Cam Belt Lock Tool
    It helps you to hold the loaded cam from rotating while installing the belts on 4 valve Ducati 749/999 Testastretta engines.
    Slide the tool between the cam belt pulleys and slide the old belt off....

  • 2 Pc. Head Timing Tool
    Belt roller timing of two-valve head.
    It provides 2 sizes : M5x0.8 and M8x1.25
    It fits most Ducati bikes....

  • Head Timing Tool M8 x 1.25
    Belt roller timing of two-valve head.
    They fit most Ducati bikes....

  • Head Timing Tool M5 x 0.8
    Belt roller timing of two-valve head.
    They fit most Ducati bikes....

  • Head Timing Tool M6 x 1.0
    Belt roller timing of two-valve head.
    They fit most Ducati bikes....

  • Bevel Single Twin Fork Cap/Engine Plug Tool
    2 sizes in one, 12mm allen used in Marzocchi fork nuts and 14mm used in engine case plugs.
    It suited for work with 1/2＂ratchet or breaker bar easily.
    Material : Stainless.

    Applications : Ducati 250/350/450/750...

  • Gear Sensor Bushing Tools
    Ideal tool for Gearbox Position Sensor.

    Fits Ducati 899, 959, 1199, 1299 Panigale, 1200, 1260 Diavel, Multistrada....

  • Front Axle Alignment Tool 30mm
    This tool allows you to help install and maintain correct alignment of the front axle while the axle nut is being tightened.
    It fits Ducati 848, 1098, 1198 and other models that use a 30 mm ID axle.

    Material : aluminum 6061 T6....

  • Front Axle Alignment Tool 25mm
    This tool allows you to help install and maintain correct alignment of the front axle while the axle nut is being tightened.
    It fits Ducati 748, 916, 996, 998, 749, 999, ST2, ST3, ST4, 620SS, 800SS, 1000SS and other models that use a 25mm ID axle.

    Material : aluminum 6061 T6....

  • 8mm Valve Shim Measuring Tools
    Work on all engines using 8mm valves.
    Sold as a pair, one is for measuring the closing shim; the other is for opening shim....

  • 7mm Valve Shim Measuring Tools
    Work on all engines using 7mm valves.
    Sold as a pair, one is for measuring the closing shim; the other is for opening shim....

  • Alternator Cover Puller
    It is essential tool to remove the left hand side cover on Ducati Engines.
    Puller provides one tool body (made from 6061 aluminum) and comes with 3 bolts (M10x1.25x50L 1 pc、M6x1.0x30L 2pcs).

    It fits 1990-2009 Ducati Models 600/620/695/696/748/749/750/800/848/851/888/900/906/907/916/996/998/999/1000/1078/1098/1100/1198 .

    ...

  • Motorcycle Valve Adjustment Kit
    It makes the valve adjusting easier.
    Fits most Triumph 500/650/750 twins 1950’s-1970’s
    Fits 7/16 SAE, British 1/4 BS, 3/16 W, 5/16 BS, 1/4 W....

  • Clutch Hub Puller
    Ideal tool for pulling the clutch hub from its taper on the main shaft.

    Fits 500/650/750 c.c. Triumphs and also BSA 500/650 twins from '66-on up.
    Threading is 20tpi.

    Material: Stainless....

  • Cam Gear Removal And Installation Tool
    This tool is absolutely essential to remove and replace the cam gears when the need to change cams and do a full engine rebuild on your Triumph twin motorcycle.

    Behind the can gears, there is not enough room to use a universal puller, but this tool helps you to remove and install them easily....

  • Crankshaft Pinion Puller
    This 3 jaw puller is essential to remove the crank pinion from the right hand crankcase.

    It must have to split the cases for a full rebuild.
    It fits all Triumph pre unit and unit twins, 650 c.c. and 750 c.c. as well as 500 c.c. and OIF Triumphs and Norton 750 and 850 motorcycles....

  • Timing Pinion Puller
    Thread Size : 1 1/8＂by 20TPI.
    Fit for Norton AJS vintage motorbike....

  • Spindle Removal Tool
    Use to remove rocker shafts of most Norton twin....

  • Pinion Extractor Tool
    For withdrawing the magneto pinion on BSA B and M Series motorcycles.
    Also use for a wide range of bikes including the BSA B31, B33, M20, M31 and Gold Star.
    5/8＂ diameter, 20TPI thread into the pinion....

  • Primary Plug Tool Set
    With 3/8＂socket drive or end wrench, both hex and socket on reverse side

    Fits the chaincase plugs of all Commando, and most mid-sixties-on Matchless and AJS, plus Norton hybrids....

  • Clutch Spring Nut Tool
    Ideal tools to make adjusting clutch pressure plate spring a snap.
    Helps you to keep tightening as the stud protrudes proud of the nut.
    Fits on Triumph, BSA, and Norton single or twin cylinder....

  • Inspection/Valve Cover Cap Tool
    This tool helps you to remove and install the large slotted inspection caps without damaging them on your Triumph, BSA and Norton motorcycle....

  • Swinging Arm Tool
    This tool fits the Triumph 4 models listed below :
    2006-2014 Daytona 675
    2011- 2014 Daytona 675R
    1994-2014 Speed Triple 1050
    2011- 2014 Speed Triple R
    2007-2014 Street Triple 675
    2008-2014 St...

  • Engine Mount Tool
    This tool fits the Triumph 3 models between 1994 and 2014.
    Applications :
    1994-2014 Speed Triple 1050.
    2011-2014 Speed Triple R.
    2006-2014 Tiger 1050.
    2012-2014 Tiger Explorer.
    2012-2014 Tiger Explorer XC.
    2013-2014 Tiger SPORT.
    2012-2014 Trophy 1215.
    2012-2014 Trophy 1215 SE....

  • Swinging Arm Adjuster Wrench
    Applications :
    Triumph Tiger 800 2011-2014 and Tiger 800XC 2011-2014....

  • Points Seal Tool
    This tool helps you to reinstall your timing cover with certainty without damaging the seal.

    It should be fit for all early unit Triumph until '69 or so....

  • Point Seal Tool
    This tool helps you to reinstall your timing cover with certainty without damaging the seal.

    It should be fit for all later unit Triumph after '68 or so.
    Material : Stainless, 28tpi....

  • Points Seals Tool
    This tool helps you to reinstall your timing cover with certainty without damaging the seal.

    It should be fit for all Norton without magneto.
    Applications : Norton Commando 750/850....

  • Cylinder Head Torque Tool
    A perfect tool for torque the two central head bolts of the last generation of Meriden twin.

    It should be fit for all Triumph Bonneville T140 750 except aftermarket big-bore kits....

  • Clutch Spring Tool
    Ideal tool to remove and replace those large clutch spring nuts.

    Fits most old British bike.
    It works on BSA and Triumph singles/twins and pre-Commando Norton.
    Material : Stainless

    Applications : Triumph, Norton and BSA motorcycles....

  • Clutch Spring Nut Tool
    Ideal tool that helps you to adjust the clutch pressure plate springs simple on your Triumph bike.

    Measures 3＂Long...

  • Top Dead Center Tool
    This TDC tool provides SAE thread and British thread on both ends.

    It helps you to find the top dead center and gets your timing wheel indexed for perfect ignition timing.
    Material : Stainless 303...

  • Amal Jet Key Removal Tool
    It is an ideal jet key tool for removal of main jet.

    Material : Stainless 303....

  • TDC Timing Ignition Tool
    Fits BSA A50 & A65 models.
    Note : Some early 1966 A50 & A65 Engine cases did not have the TDC Hole....

  • Shock Preload Adjusting Tool
    It helps you to adjust preload without damaging the shock spring collars.

    It fits 35mm to 75mm spring collars....

  • Cartridge Rod Holding Plate
    Material : Stainless.

    Fits 10 to 12.5mm rods....

  • Cartridge Rod Holding Plate
    Material : Stainless.

    Fits 13 to 14mm rods....

  • Fork Seal Head Tool
    This tool allows you to remove and replace the seal head assembly from the fork tube in 41mm and 43mm BPF

    It helps you to change fork springs without valve disassembly....

  • Shock Reservoir Cap Removal Tool
    This Tool threads onto the Schrader Valve which located on the reservoir cap.Helps you to install/remove it easily....

  • Nitrogen Needle Kit
    Used to fill shocks with self-sealing type rubber valve....

  • 35mm Fork Cap Wrench
    It is made from Polyamides (PA) with fiber and that will allow you to remove your fork cap without damaging it....

  • 32mm Fork Cap Wrench
    It is made from Polyamides (PA) with fiber and that will allow you to remove your fork cap without damaging it....

  • 30mm Fork Cap Wrench
    It is made from Polyamides (PA) with fiber and that will allow you to remove your fork cap without damaging it....

  • 2 In 1 Fork Cap Tool
    Double end design allows you to remove the cartridge on Showa SFF forks and twin chamber Showa forks.
    Tool holds cartridge so it can be removed from fork cap.
    This tool will help you to reduce risk of damage during disassembly.
    1/2 inch square drive....

  • Shock Bladder Puller
    This puller threads can reach onto the Schrader valve on the shock reservoir and make the bladder removal be easier....

  • 49mm Dual Chamber Fork Cap Wrench
    A must have tool to remove the fork cap (cartridge) on dual chamber closed cartridge forks on Honda (except 2010 CRF250R) and Yamaha later motorcycles.

    The 12.5mm slot can hold the damper rod while removing the rebound bolt at the bottom of the fork.
    Material : Aluminum 6061-T6....

  • 50mm WP Dual Chamber Fork Cap Wrench
    A must have tool to remove the fork cap (cartridge) on WP 4860 MXMA dual chamber closed cartridge (WP USD 48 mm) forks on KTM later models

    The 12mm slot can hold the damper rod while removing the rebound bolt at the bottom of the fork.
    Material : Aluminum 6061-T6....

  • Shock Bushing Driver Set
    Ideal tool for removing bush from shock.

    Instructions :

    1. Place block on solid bench.
    2. Place shock bush over appropriate sized hole.
    3. Use appropriate drift to remove the bush.
    4. Knock bush out of shock.
    5. Use copper mallet to avoid damaging the drift.
    ...

  • Fork Compression Valve Removal Tool
    Ideal tool to remove the compression valve from cartridge.

    19mm drive hex with 36mm octagon.
    Made from 6061-T6 aluminum....

  • 50mm Fork Cap Wrench
    For SHOWA frond forks.

    Has a 3/8＂square hole available for torque wrench.
    As a rod holder, the opposite end of the wrench also can be used to hold the piston rod when removing the piston inner cartridge of front forks....

  • 49mm Fork Cap Wrench
    For KYB frond forks.

    Has a 3/8＂square hole available for torque wrench.
    As a rod holder, the opposite end of the wrench also can be used to hold the piston rod when removing the piston inner cartridge of front forks....

  • Fork Cap Wrench＜46mm 50mm＞
    Designed to remove the fork caps and adjust compression dampening on late-model CRs. and RMs. 46mm & 50mm....

  • Fork Cap Wrench＜49mm / 50mm＞
    Designed to remove the fork caps and adjust compression dampening on late-model CRs. and RMs. 49mm & 50mm....

  • Fork Cap Wrench＜45mm / 50mm＞
    Designed to remove the fork caps and adjust compression dampening on late-model CRs. and RMs. 45mm & 50mm....

  • Master Link Pliers
    Fits on 25, 415, 420, 425, 428 chains.

    Insert the jaws into the master link; tighten the forcing screw for squeeze of handles until link is separated....

  • Chain Breaker
    Ideal tool for use on 420, 428, 520, 525 and 530 chain.
    The handle can be folded away for easy storage....

  • Chain Breaker
    Ideal tool with 2 hardened pins in 4.0mm and 4.8mm.
    Chains from 420 to 620.
    The handle can be folded away for easy storage....

  • 14mm Top Dead Centre Tool
    Ideal tool to find TDC fast and easily as you rotate the engine and piston rises up the center indicator.

    Fits all 14mm spark plug holes.
    Material: Stainless 304...

  • 10 & 12mm Top Dead Centre Tool
    Ideal tool to find TDC fast and easily as you rotate the engine and piston rises up the center indicator.

    Fits 10mm or 12mm spark plug holes.
    Material: Stainless 304...

  • Carburetor Float Level Gauge
    It is adjustable to fit most carburetors.

    For measuring float level height between the float and carburetor gasket surface....

  • Piston Detaching Tool
    Ideal tool to detach a piston from the disk brake base of a motor vehicle....

  • Cleaning Tool For Carburetor Nozzle 20pcs
    Easy to Cleaning and suitable for all kind of Carburetor Nozzle 0.45~1.5mm....

  • Cleaning Tool For Carburetor Nozzle 16pcs
    Easy to Cleaning and suitable for all kind of Carburetor Nozzle 1.5-3.0mm....

  • FCR Fuel Mixture Screw Adjuster
    It works on FCR Keihin carburetors.
    Designed to replace the hard to reach stock fuel screw.
    Adjust at the track or out on the trail easily.
    Number knob for accurate setting.
    Comes with one spring, two washers and o-rings.

    Material : Aluminum 7075...

  • Carburetor Float Bowl Wrench
    Fits most off-road and dual sport motorcycles.

    Designed to remove 17mm float bowl drain plugs....

  • Rim Protection Tools
    Ideal tools to protect your wheel and avoid damaging the rim surface while changing tires or repairing tubes.

    Cords to keep the Rim Protection Tools from getting lost inside your tire are included for easy use....

  • Belt Tension Gauge
    This tool can be used to adjust belt tension on most motorcycles equipped with a secondary drive belt.

    This tool provides a simple way to confirm the belt for proper tension....

  • Off-Road Tire Tool
    Good auxiliary tool for tire irons when replacing the tire of off-road wheels and also a must for installing tubes.

    Provides an easy way to push the tire bead down into the drop center of the rim on off-road wheels while using tire irons to change tires....

  • Large Multi-Valve Tool
    These tools are purpose to save time necessary when replacing valves in modern 16 – to 20 – valve heads.
    Large tool works on valves of 4-valve-per-cylinder heads
    (5.5 mm valve stem diameter or larger with under 40 lbs. seat pressure).
    Small tool works on valves of 4-and 5-valve-per-cylinder heads
    (5mm valve stem diameter or smaller)....

  • Small Multi-Valve Tool
    These tools are purpose to save time necessary when replacing valves in modern 16 – to 20 – valve heads.
    Large tool works on valves of 4-valve-per-cylinder heads
    (5.5 mm valve stem diameter or larger with under 40 lbs. seat pressure).
    Small tool works on valves of 4-and 5-valve-per-cylinder heads
    (5mm valve stem diameter or smaller)....

  • Valve Core Remover
    Ideal tool to remove and install standard valve cores in tubed or tubeless valve stems (Schrader valve) easily....

  • Brake And Clutch Cable Injector
    This tool is purpose designed to fix the brake and clutch cable when injecting the lubrication oil....

  • Flywheel Puller M33 x 1.5
    33mm x 1.5 right hand thread (male).
    Lubricate all areas before use....

  • Flywheel Puller M27 x 1.25
    27mm x 1.25 right hand thread (male).
    Lubricate all areas before use....

  • Flywheel Puller M35 x 1.5
    35mm x 1.5 right hand thread (female).
    Lubricate all areas before use....

  • Flywheel Puller M20 x 1.5
    Bolt with 20mm x 1.5 right hand thread (male).
    Lubricate all areas before use....

  • Flywheel Puller M27 x 1.0
    27mm x 1.0 left hand thread (male)
    Lubricate all areas before use....

  • Flywheel Puller M30 x 1.5
    30mm x 1.5 right hand thread (male).
    Lubricate all areas before use....

  • Double End Flywheel Puller
    27mm x 1.25 and 26mm x 1.5 right hand thread (male).
    Lubricate all areas before use....

  • Double End Flywheel Puller
    33mm and 30mm x 1.5 right hand thread (male).
    Lubricate all areas before use....

  • Flywheel Puller M27 x 1.0 Lh Ext
    M27 x 1.0 Lh Ext.
    Fits most late-model MX bikes....

  • Tire Bead Tool
    It is designed to push the tire bead down into the drop center of the rim without fighting while installing or repairing your off-road tires.
    It holds the tire bead down in the drop center of the rim during tire changes and makes tire changes easier.
    The securing thumbscrew keeps rims scar-free.
    Material: 6000 series aluminum....

  • Deluxe Tire Bead Tool
    It is designed to push the tire bead down into the drop center of the rim without fighting while installing or repairing your off-road tires.
    It holds the tire bead down in the drop center of the rim during tire changes and makes tire changes easier.
    The securing thumbscrew keeps rims scar-free.
    Material: 6000 series aluminum with stainless screw....

  • Steering Stem Bearing Race Removal Tool
    It provides a simple way to remove the bearing race on a steering stem.
    It works on most all stems.
    Opening size : 30mm-68mm....

  • Motorcycle Brake Bleeder
    Aids in the bleeding and servicing of hydraulic brakes.
    It allows user easy to make bleeding brakes by oneself.
    The unique check valve design makes fluid and air to escape while preventing air from re-entering the system....

  • 4-In-1 Hex Axle Tool＜17, 19, 22, 24mm＞
    Made from 7075-T6 aluminum for strength-weights are extremely light.
    Ideal for touring or off-road tool kit....

  • 4-In-1 Hex Axle Tool＜17, 19, 22, 24mm＞
    Heavy duty CrMo steel construction for shop use....

  • 2-In-1 Axle and Fork Tool
    Use to open the SHOWA air fork of the Honda CRF 250-2015.
    A good idea to combine an axle and a fork tool as well.
    Material : Heavy duty CrMo steel construction....

  • Valve Shim Tool
    Designed to adjust valve clearance on Suzuki and Yamaha twin-cam models.
    It can hold the valve spring bucket down while removing the adjusting shims....

  • Valve Adjustment Tool
    Ideal tool to adjust valve especially when space is limited. It comes a square hole on both sides with an edge length of exactly 3 mm and 4 mm....

  • Wheel Bearing Retainer Tool
    This bearing retainer installation and removal tool has 47mm diameter and the teeth width are 4.6mm....

  • Clutch Puller＜M18 x 1.5＞
    Application : All Yamaha 4 strokes, 84-94 PZ480, 94-99 V-Max 500/600/700, 00-06 SX/SXR/Viper/Venom...

  • Clutch Puller＜M14 x 1.0＞
    Applications : Ski-doo liquid twin 443/454/494/583/617/643 1990-1999 and fan cooled twin 440/503 1997-2001...

  • Clutch Puller＜M14 x 1.5＞
    Application : Ski-doo 99-15 two stroke/four stroke,95-01 triples, 93-99 670 twin....

  • Clutch Puller＜M14 x 1.0＞
    Applications : Ski-doo 583 clutches....

  • Heavy Duty Spring Hook
    Ideal tool to remove exhaust pipe springs.
    It also can be used for cotter pins, seat or tank holding springs, side-stand springs, and other troublesome springs.
    Handle w/vinyl....

  • Gear Holder
    Tightens gears by inserting this tool between gears to prevent rotating when removing & installing primary drive gear / clutch outer....

  • Clutch Nut Socket
    Ideal tool to loosen and tighten the Clutch Nut.
    Made by heavy-duty carbon steel with high accuracy.
    Tools comes with a 1/2＂square hole that fit a ratchet/torque wrench.

    Application :
    Honda CBX1000 1979-1982
    Honda V65 Magana 1983-1986...

  • wingarm Socket Tool
    Ideal tool to loosen and tighten the Swing Arm Nut.
    Made by heavy-duty carbon steel with high accuracy.
    Tools comes with a 1/2＂square hole that fit a ratchet/torque wrench.

    Application :
    Honda RVF 400 RR(NC35)
    Honda RVF 400 RT(NC35)...

  • Top Triple Nut Socket Tool
    Ideal tool to loosen and tighten the Top Triple Nut.
    Made by heavy-duty carbon steel with high accuracy.
    Tools comes with a 1/2＂square hole that fit a ratchet/torque wrench.
     
    Application :
    Honda GL1000 1977-1979
    Honda GL1100 1980-1983
    Honda GL1200 1984-1987
    ...

  • Engine＜Frame＞Socket Set
    Ideal tool to undo and tighten the adjusting and locking nut on the frame when removing and installing the engine.
    Set comes with a 1/2＂square hole that fits a standard ratchet or torque wrench.

    Fits Honda VFR750F 1990-1997 and CBR1100X 1997 to 2003....

  • 14mm TDC Indicator Stop Tool
    Used to accurately locate top dead center of the piston’s stroke.
    Use this tool, you will not have to remove the plug and measure it.
    Use this tool with a cam degree wheel to dial in the cam for maximum horsepower....

Categories

Category
  • Tools & Equipment
    • Loading ...

    :
    :


    Legend
    Available Timeslot
    Scheduled Appointment
    Personal Appointments
    Appointment Request
    Blocked Timeslot
    Restricted Timeslot
    Cancelled
    Declined
    Call us at 855-MC-SHOWS