DCF-35 Multi-Purpose HD Flusher - Cooling Systems, Intercoolers
and On-Vehicle Ford 6.7L EGR System Carbon Cleaner
The Flo-Dynamics DCF-35, Diesel Component Flusher, will flush and clean CAC/intercoolers, radiators & cooling systems and other diesel system components of carbon, oil, and other foreign materials. The DCF-35 is also specifically engineered to clean a Ford 6.7L EGR Valve and Cooler on-Vehicle! Flush and clean a 6.7L EGR system on-vehicle in one hour or less depending on the carbon build up. Unlike other aggressive cleaners on the market that attacks aluminum, our cleaner is aluminum safe that softens and dissolves carbon and breaks down oil without leaving a harmful film. Flushing at up to 45 GPM will clean out the entire component of carbon, foreign fluids, and debris. Using a high-performance heater along with circulation accelerates the heating process obtaining a safe flushing temperature of 130 degrees F in approximately 90 minutes, unlike other units that can take a half a day to warm up.
Features
- Clean and flush Intercoolers and cooling systems after a turbo or engine failure in approximately 1-3 hours plus R&R time
- Clean carbon from a Ford 6.7L EGR system on-vehicle in approximately one hour plus R&R time
- Easily selected flush times 15, 30, 45, 60, 90, and 120 minutes
- 45 GPM 120V Pump
- 1300W 120V Heater – Heats up cleaner and water solution to 130 deg F in approximately 90 minutes
- Easy and safe to use with GFI protection
- 35-gallon tank allows flushing large intercoolers and radiators
- Easy mobility with heavy duty casters
- Inner tank circulation mode for faster warm up
- Flo-Dynamics RTO Component System Cleaner available P/N 40201131
- Ford 6.7L EGR system adapter flush kit available
- Component or system pressure check kit available
- Step Adapters to connect to 5/8”– 3” component inlets and outlets available
TTCF-9A P/N 40400060
Heavy Duty Heated Component Flusher – Variable High Flow Transmission Cooler System and Hydraulic System Flusher
The Flo-Dynamics TTCF-9A-VHF, Variable High Flow, Hydraulic System Flusher, will flush and clean transmission coolers and lines or any hydraulic system of contamination, sludge and varnish deposits, and particles from a failed transmission. The TTCF-9A-VHF with an adjustable flow rate from 1 – 7.5 GPM was specially developed for heavy duty transmission cooling systems requiring high flow rates. Using the same hydraulic fluid as used in the hydraulic system being flushed and cleaned, a user can select from multiple flush cycles 15-120 minutes until the system is clean by checking the re-usable 64-micron Oberg filter. The TTCF-9A-VHF heating to a preset 140 deg F in 45 minutes is fast and easy using the heating circulation mode. Each flush cycle auto injects air at precise intervals to agitate the fluid causing a scrubbing action removing trapped debris and solidified waxy varnish deposits. Simply switch flow direction without removing service hoses between flush cycles with the reverser valve. From the conveniently located control panel observe system flow, pressure, temperature, total hours run, filter timer, and easily select pump on/off, heater on/off, flush cycles and manual air purge.
Features
- Powerful ¾ HP motor
- For best performance use two separate 15-amp circuits
- 13’ HD ¾” service hoses
- 10-gallon tank allows flushing large and small systems
- Adjustable flow rate of 1 – 7.5 GPM enables cleaning small to large flow hydraulic systems
- Low fluid sensor shuts off heater and pump
- Re-useable 64-micron Oberg filter with “T” handle makes checking cleanliness easy
- Reverser valve allows to easily reverse flow without removing service hoses
- Air injection to agitate system causing a scrubbing action removing trapped debris and solidified waxy varnish.
- Selectable flush cycles choose from continuous or 15-120 minutes with or without auto air injection
- Auto stop and alert at flush cycle end
- Air purge allows for easy fluid removal from system and service hoses
- Spin-on filter timer showing hours used
- Replaceable NBP-2 non-bypass Spin-On Filters with magnets available P/N 40300272
- Allison transmission adapter kit P/N 40300283 Includes -8 (1/2 JIC), -12 (3/4 JIC), -16 (1” JIC), -20 (1-1/4” JIC)